|
Standard Actuators · Power Supplies
ETREMA Products proudly uses and recommends Titan Series AC Power Sources.
The TITAN SERIES of AC power sources delivers a much higher level of performance than has been
previously obtained by competitive linear products. A totally new design approach using
patented, switchmode, thick-film power hybrid circuitry enables the unit to deliver an
impressive 70% to 82% power transfer efficiency across the full output voltage range,
resulting in cool operation at any output level. In sharp contrast, traditional linear
AC power sources have an efficiency of only 5% to 50%, depending on output level and
load conditions. In addition, since the output stages have four-quadrant topology,
the unit is capable of delivering its full rated output voltage and current without
derating into any reactive load with any power factor without any excessive heating,
shutdown, or possible damage as would be encountered in the traditional linear
amplifier designs.
Reactive power is recirculated back to the unit with 90% efficiency, as opposed to being
wasted and dissipated in the form of excess heat in conventional designs. This fact
alone dramatically cuts utility bills for both operating the unit itself and air
conditioning for the housed facility. Reliability and safety are greatly enhanced as
the operator need not check an instruction manual for a derating curve, since the power
factor may change, not always be known, or be difficult to measure. All these application
headaches are eliminated by specifying the TITAN SERIES AC power sources with their
completely protected outputs and no confusing derating curves.
HALF the Price, Size, and Weight! TWICE the Bandwidth, Ruggedness, and Flexibility!
|
Description |
Volts RMS |
Amps RMS |
Height/Inches |
Width/Inches |
Depth/Inches |
Weight/Lbs. |
Comments |
| ACP-01 |
165 VA Mainframe |
0-130/260 |
1.4/0.7 |
5.25 |
19 |
13.5 |
31 |
Includes External Input Module EIM-011 |
| ACP-01E |
165 VA Mainframe |
0-130/260 |
1.4/0.7 |
5.25 |
19 |
13.5 |
31 |
European Version with EIM-01 |
| ACP-01A |
165 VA Mainframe |
0-130/260 |
1.4/0.7 |
5.25 |
19 |
13.5 |
31 |
Includes sinewave oscillator MOS-012 |
| ACP-01AE |
165 VA Mainframe |
0-130/260 |
1.4/0.7 |
5.25 |
19 |
13.5 |
31 |
European Version with MOS-01 |
| ACP-02 |
500 VA Mainframe |
0-130/260 |
4.0/2.0 |
5.25 |
19 |
13.5 |
38 |
Includes External Input Module EIM-011 |
| ACP-02E |
500 VA Mainframe |
0-130/260 |
4.0/2.0 |
5.25 |
19 |
13.5 |
38 |
European Version with EIM-01 |
| ACP-02A |
500 VA Mainframe |
0-130/260 |
4.0/2.0 |
5.25 |
19 |
13.5 |
38 |
Includes sinewave oscillator MOS-012 |
| ACP-02AE |
500 VA Mainframe |
0-130/260 |
4.0/2.0 |
5.25 |
19 |
13.5 |
38 |
European Version with MOS-01 |
| ACP-03 |
1 kVA Mainframe |
0-130/260 |
8.0/4.0 |
5.25 |
19 |
13.5 |
56 |
Includes External Input Module EIM-011 |
| ACP-03A |
1 kVA Mainframe |
0-130/260 |
8.0/4.0 |
5.25 |
19 |
13.5 |
56 |
Includes sinewave oscillator MOS-012 |
|
1 The EIM-01 external input module is used to safely isolate and input an external
drive signal into the ACP-01, -02, or -03 AC power mainframes. The unit can accept input
from laboratory oscillators, programmable oscillators, or, when used as a slave unit,
from an MOS-01 oscillator. Input is completely isolated with 1500VAC breakdown and
excellent common mode rejection. A recessed +/- 8% gain adjustment control is also
provided.
2 The MOS-01 manual oscillator module is used as a quality, general purpose
sinewave oscillator and digital readout monitoring system in the ACP-01, -02, or -03 AC
power mainframes. The unit has a guaranteed operating range of 45 Hz to 20 kHz, which
is covered in three one-decade scales. The LCD digital metering system is
switch-selectable to readout either frequency voltage or current. A toggle switch
selects the input for the attached mainframe to originate from the manual oscillator
itself or from an external laboratory or programmable oscillator source.
With oscillator mode switch to Internal position, the BNC connector delivers the
signal to drive additional slave units or for oscilloscope sync or monitoring.
BNC input/output is completely isolated with 1500 VAC breakdown and excellent
common mode rejection.
Call Etrema Products or email customer.service@etrema-usa.com for a price quotation today! Most quotations returned in under 24 hours!
|
